
Hawkesbury, NSW
Custom ute trays & truck trays
JV Steel Fabrication Services builds custom ute trays and truck trays to spec in the Hawkesbury, NSW. Not just the tray: headboards, under-body toolboxes, trundle drawers, tray sides and clearance lights, removable racks and frames, and rock sliders for 4x4s.
From his own jobs
What JV Steel has built
Tell Jordan the vehicle and what it has to carry, send a photo if you can, and the tray is worked out around it. Quotes are free.
- Custom trays built to spec, for utes and light trucks
- 3-inch headboards
- Under-body toolboxes and trundle drawers
- Tray sides and clearance lights
- Removable racks and plant frames
- Rock sliders, made to fit the vehicle
- Mirror brackets and bull bar modifications
- A mirror-finish stainless memorial sign, built into a tray
Built around the vehicle and the work
A good tray starts with two questions: what is the vehicle, and what will it carry every day? The answers decide the size, where the toolboxes go, whether the headboard carries a rack, and how the load is tied down.
The 79 Series LandCruiser tray on this page shows how far that goes on one build: a 3-inch headboard, two under-body toolboxes, a trundle drawer, tray sides, clearance lights and a mirror-finish stainless memorial sign.
The work
Jobs Jordan has built
Tap a job for the photos and what went into it, from Jordan’s own posts.




Steel or aluminium tray?
As a general guide, an aluminium tray is lighter, which leaves more of the vehicle's payload for what you carry, and it does not rust. A steel tray is strong, takes knocks well and is usually the cheaper metal. Which suits you depends on the vehicle, the load and the work it does.
Not sure? That is part of the conversation with Jordan before anything is cut.
Rock sliders for 4x4s
Rock sliders run along the sill under the doors and take the hits off-road instead of the body. The pair on this page were custom made to fit a Nissan Patrol, then fitted along the sill.
Straight answers
Questions people ask
The questions people type into Google about this kind of work, answered plainly. Anything else, ask Jordan.
Steel or aluminium ute tray: which is better?
It comes down to what you carry and where you drive. Aluminium is much lighter, which leaves more of the ute's carrying limit for your load, and it does not rust. Steel is heavier but tough under rough work and simple to repair, and it needs paint, powder coat or galvanising to keep rust away.
Tell Jordan the vehicle and the work, and he can talk you through which suits.
How much does a custom ute tray cost?
It depends on the size of the tray, steel or aluminium, and what goes on it: headboard, toolboxes, drawers, lights, finish. Call Jordan with your ute's make and model and what you want on it. The quote is free.
Do I need an engineer's certificate for a tray on my ute in NSW?
It depends on the change. Transport for NSW says a vehicle with minor modifications may not need certification, but major modifications must be assessed by a licensed certifier before the vehicle can be registered. Its information sheet VSI 06 (light vehicle modifications) explains which changes need a certificate, so check it, or ask Transport for NSW, before the build.
Source: Vehicle standards information sheets, Transport for NSW
What are rock sliders for, and are they worth it?
Rock sliders are strong rails fixed under the doors. They take the hit instead of the sills and doors when you drive over rocks or deep ruts, and those panels are costly to repair. They are worth it for anyone who drives rocky or rutted tracks.
Can you use rock sliders as steps?
Many sliders are built with a flat top or a step plate so they work as a step too. Ordinary side steps are made for climbing in, not for carrying the vehicle's weight on a rock. Say if you want yours to double as a step when you ask about them.
Other work
More from the workshop
Every kind of job JV Steel has built, in mild steel, stainless and aluminium.
Get a price
Ask about ute & truck trays
JV Steel Fabrication Services
- Fabricator
- Jordan Vella
- Phone
- 0468 080 200
- jvsteelfab@gmail.com
- Base
- The Hawkesbury, NSW
- Metals
- Mild steel · Stainless · Aluminium
- Trading
- Since 2020
- ABN
- 93 955 183 752
Hours
- Monday to Friday
- 6:30am to 8pm
- Saturday
- 7am to 6pm
- Sunday
- 7:30am to 4pm
After-hours work available.



